Manual

How do I register my Target Blu Eye?

Before registering the system, mount Blu Eye in the car and install the supplied antenna using Installer Mode (factory installed on Blu Eye). This is the only way to guarantee the optimal functioning of Blu Eye.

If you have a Blu Eye that has been installed in another car before, please download and install Installer Mode first to determine an interference-free location for the antenna.

Get your activation file

  1. Turn off the car's ignition. This also disables the Blu Eye system.
  2. Insert the supplied SD card into the SD card slot of your Blu Eye.
  3. Switch on the ignition.
  4. Your Blu Eye's unique serial number will now be copied to the SD card.
  5. All LED’s will turn on for 5 seconds. As soon as the 5 LED’s of the signal strength indicator go out and only the 2 blue LED’s are lit, this procedure is finished. This takes approximately 5 seconds.
  6. Switch off the ignition.
  7. Remove the SD card from your Blu Eye.
  8. Insert the SD card into the SD card slot of your PC or Mac.
  9. Press the "Browse" button to locate the appropriate file.
  10. You will be prompted to select the activation file with a unique serial number (UNIQUEID.TXT) on the SD card. To do this, click on "Browse". Select the SD card on your computer and then open the file "UNIQUEID".
  11. Now click on "upload file".
How do I activate my Target Blu Eye?

After Blu Eye has been installed and connected and the antenna placement has been tested with Installer Mode, you need to activate the system.

To do this, proceed as follows:

  1. Download the firmware.
  2. Copy these files to the SD card (Do not put the files in a folder and make sure that the card does not contain any other files).
  3. Remove the SD card from your PC or Mac.
  4. Switch off Blu Eye by switching off the car’s ignition.
    If Blu Eye remains on for some time after turning off the ignition (canbus dependent), disconnect the Blu Eye's power plug to turn off the system.
  5. Insert the SD card into the SD card slot of your Blu Eye.
  6. Switch on the ignition. IMPORTANT: Never interrupt the power to your Blu Eye system during the update process.
  7. All LEDs will turn on for 5 seconds. During this initial registration and update process, it takes approximately 30 seconds to copy the files to Blu Eye. Several LED’s light up during the update. At the end of this process, the LEDs step from red to green. The process is complete when the last green LED is extinguished.
How do I activate my Target Blu Eye 2?

IMPORTANT

  • Connect the display (or both displays when using a LED and LCD display side by side) to the Blu Eye receiver.
  • Do not install the system yet, but connect it to the car's 12V power supply.
  • Download and install the activation file (firmware) for Blu Eye 2.

Obtain and install your activation file

(LED display)

  1. Turn off the car's ignition. This also disables the Blu Eye system.
  2. Insert the supplied USB drive into the USB connector of Blu Eye.
  3. Switch on the ignition: the “Device List” will now be copied to the USB drive. This procedure is complete when the status LED lights up alternately red and white.
  4. Switch off the ignition.
  5. Remove the USB drive from your Blu Eye.
  6. Plug the USB drive into the USB connector of your PC or Mac.
  7. Specify a reference for the Blu Eye. For example, the name of the customer, the vehicle’s registration number, or the car make and type. You can then easily find the system back later to provide it with an update.
  8. Click on “Select file” to select the appropriate device list in the “devices” folder on the USB drive.
  9. Click “Upload file”.
  10. You will see an overview of the connected devices. Click “Download Firmware”.
  11. Copy the downloaded file to the “Firmware” folder on the USB drive.
  12. Remove the USB drive from your PC or Mac.
  13. Insert the USB drive into the USB connector of Blu Eye.
  14. Switch on the ignition: Blu Eye will now copy the new firmware from the USB drive. The status LED lights up white. When the status LED is green, the firmware has been successfully saved and the system is ready for use.
  15. Turn off the ignition and remove the USB drive from the Blu Eye's USB connector.
How do I update the firmware on my Blu Eye 2?

Below you will be guided step by step through the procedure to update the firmware on your Blu Eye 2.

  1. Click "Download firmware": The new firmware will be saved with file name [reference] in the download folder on your PC or Mac.
  2. Copy this file to the "Firmware" folder on the USB drive.
  3. Turn off the car's ignition. This also disables the Blu Eye system.
  4. Insert the USB drive into the USB connector of Blu Eye.
  5. Switch on the ignition: Blu Eye will now copy the new firmware from the USB drive. The status LED lights up white. When the status LED is green, the firmware has been successfully saved and the system is ready for use.
  6. Turn off the ignition and remove the USB drive from the Blu Eye's USB connector.
How can I change the configuration of my Blu Eye 2?

When expanding the system with one or more modules or when replacing a module, the new module (or more modules) must be included in the configuration. Proceed as follows:

  1. Turn off the car's ignition. This also disables the Blu Eye system.
  2. Insert the supplied USB drive into the USB connector of Blu Eye.
  3. Switch on the ignition: the new “Device List” will now be copied to the USB drive.
  4. Blu Eye starts up with a red status LED and an audio signal: this is a warning that an unknown module (device) has been detected that is not yet active. Then the status LED turns green.
  5. Switch off the ignition.
  6. Remove the USB drive from your Blu Eye.
  7. Plug the USB drive into the USB connector of your PC or Mac.
  8. Select the system for which you want to change the configuration.
  9. Click “modify configuration”.
  10. Click "Select file" to select the appropriate device list in the "devices" folder on the USB drive.
  11. Click “upload file”.
  12. You will now see an overview with all connected devices (green) and/or removed devices (red).
  13. Is this correct: click “save changes”.
  14. Click "Download firmware": The new firmware will be saved with file name [reference] in the download folder on your PC or Mac.
  15. Copy this file to the "Firmware" folder on the USB drive.
  16. Turn off the car's ignition. This also disables the Blu Eye system.
  17. Insert the USB drive into the Blu Eye's USB connector.
  18. Switch on the ignition: Blu Eye will now copy the new firmware from the USB drive. The status LED lights up white. When the status LED is green, the firmware has been successfully saved and the system is ready for use.
  19. Turn off the ignition and remove the USB drive from the Blu Eye's USB connector.

Home Manual